 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| (R) LE00AB/C SERIES VERY LOW DROP VOLTAGE REGULATORS WITH INHIBIT s s s s s s s s s VERY LOW DROPOUT VOLTAGE (0.2V TYP.) VERY LOW QUIESCENT CURRENT (TYP. 50A IN OFF MODE, 0.5mA IN ON MODE, NO LOAD) OUTPUT CURRENT UP TO 100 mA OUTPUT VOLTAGES OF 1.25; 1.5; 2.5; 2.7; 3; 3.3; 3.5; 4; 4.5; 4.7; 5; 5.2; 5.5; 6; 8V INTERNAL CURRENT AND THERMAL LIMIT ONLY 2.2F FOR STABILITY AVAILABLE IN 1% (A) OR 2% (C) SELECTION AT 25 oC SUPPLY VOLTAGE REJECTION: 80 db (TYP.) TEMPERATURE RANGE: -40 TO 125 oC SO-8 DESCRIPTION The LE00 regulator series are very Low Drop regulators available in SO-8 and TO-92 packages and in a wide range of output voltages. The very Low Drop voltage (0.2V) and the very low quiescent current make them particularly suitable for Low Noise Low Power applications and specially in battery powered systems. They are pin to pin compatible with the older L78L00 series. Furthermore in the 8 pin configuration (SO-8) they employ a Shutdown Logic Control (pin 5, TTL compatible). This means that when the device is used as a local SCHEMATIC DIAGRAM TO-92 regulator, it's possible to put in stand by a part of the board even more decreasing the total power consumption. In the three terminal configuration (TO-92) the device is even in ON STATE, mantaining the same electrical performances. It needs only 2.2F capacitor for stability allowing room and cost saving effect. September 1998 1/25 LE00AB/C ABSOLUTE MAXIMUM RATING Symbol Vi Io Pt ot T stg To p DC Input Voltage Output Current Power Dissipation Storage Temperature Range Operating Junction Temperature Range Parameter Value 20 Internally limited (*) Internally limited (*) - 40 to 150 - 40 to 125 o o Unit V C C (*) Our SO-8 package used for Voltage Regulators is modified internally to have pins 2, 3, 6 and 7 electrically commoned to the die attach flag. This particular frame decreases the total thermal resistance of the package and increases its ability to dissipate power when an appropriate area of copper on the printed circuit board is available for heatsinking. The external dimensions are the same as for the standard SO-8 TEST CIRCUITS Note: If the Inhibit pin is left floating, the regualtor is in ON mode. However, to avoid any noise picking-up, it is suggested to ground it when 2/25 LE00AB/C CONNECTION DIAGRAM AND ORDERING NUMBERS (top view) BOTTOM VIEW pin 1 = OUT pin 2 = GND pin 3 = IN SO-8 TO-92 ORDERING NUMBERS Type LE12AB LE12C LE15AB LE15C LE25AB LE25C LE27AB LE27C LE30AB LE30C LE33AB LE33C LE35AB LE35C LE40AB LE40C LE45AB LE45C LE47AB LE47C LE50AB LE50C LE52AB LE52C LE55AB LE55C LE60AB (*) LE60C (*) LE80AB (*) LE80C (*) LE120AB (*) LE120C (*) (*) Available on request SO-8 LE12ABD LE12CD LE15ABD LE15CD LE25ABD LE25CD LE27ABD LE27CD LE30ABD LE30CD LE33ABD LE33CD LE35ABD LE35CD LE40ABD LE40CD LE45ABD LE45CD LE47ABD LE47CD LE50ABD LE50CD LE52ABD LE52CD LE55ABD LE55CD LE60ABD LE60CD LE80ABD LE80CD LE120ABD LE120CD LE12ABZ LE12CZ LE15ABZ LE15CZ LE25ABZ LE25CZ LE27ABZ LE27CZ LE30ABZ LE30CZ LE33ABZ LE33CZ LE35ABZ LE35CZ LE40ABZ LE40CZ LE45ABZ LE45CZ LE47ABZ LE47CZ LE50ABZ LE50CZ LE52ABZ LE52CZ LE55ABZ LE55CZ LE60ABZ LE60CZ LE80ABZ LE80CZ LE120ABZ LE120CZ TO-92 Output Voltage 1.25 V 1.25 V 1.5 V 1.5 V 2.5 V 2.5 V 2.7 V 2.7 V 3V 3V 3.3 V 3.3 V 3.5 V 3.5 V 4V 4V 4.5 V 4.5 V 4.7 V 4.7 V 5V 5V 5.2 V 5.2 V 5.5 V 5.5 V 6V 6V 8V 8V 12 V 12 V 3/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE12AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 2.5 to 18 V, Io = 0.5 mA Vi = 2.8 V Io = 0.5 to 100 mA ON MODE Vi = 2.5 to 18 V Io = 0 mA Vi = 2.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 3.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 3.3 V Io = 10 mA, Vi = 3.3 V -25 Typ. 1.25 Max. 1.275 1.3 18 Unit V V V mA mV mV mA mA A dB dB dB V V 3 3 0.5 1.5 50 82 77 60 50 1.25 15 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 0.8 V V A F ELECTRICAL CHARACTERISTICS FOR LE12C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 2.5 to 18 V, Io = 0.5 mA Vi = 2.8 V Io = 0.5 to 100 mA ON MODE Vi = 2.5 to 18 V Io = 0 mA Vi = 2.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 3.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA -40 < Ta < 125 oC o Test Conditions Io = 10 mA, Vi = 3.3 V o Io = 10 mA, Vi = 3.3 V -25 Typ. 1.25 Max. 1.275 1.3 18 Unit V V V mA mV mV mA mA A dB dB dB V V 3 3 0.5 1.5 50 82 77 60 50 1.25 20 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 0.8 V V A F 4/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE15AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 2.5 to 18 V, Io = 0.5 mA Vi = 2.8 V Io = 0.5 to 100 mA ON MODE Vi = 2.5 to 18 V Io = 0 mA Vi = 2.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 3.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 3.5 V Io = 10 mA, Vi = 3.5 V -25 Typ. 1.5 Max. 1.53 1.56 18 Unit V V V mA mV mV mA mA A dB dB dB V V 3 3 0.5 1.5 50 82 77 60 50 1 15 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 0.8 V V A F ELECTRICAL CHARACTERISTICS FOR LE15C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 2.5 to 18 V, Io = 0.5 mA Vi = 2.8 V Io = 0.5 to 100 mA ON MODE Vi = 2.5 to 18 V Io = 0 mA Vi = 2.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 3.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA -40 < Ta < 125 oC o Test Conditions Io = 10 mA, Vi = 3.5 V o Io = 10 mA, Vi = 3.5 V -25 Typ. 1.5 Max. 1.53 1.56 18 Unit V V V mA mV mV mA mA A dB dB dB V V 3 3 0.5 1.5 50 82 77 60 50 1 20 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 0.8 V V A F 5/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE25AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 3.2 to 18 V, Io = 0.5 mA Vi = 3.5 V Io = 0.5 to 100 mA ON MODE Vi = 3.5 to 18 V Io = 0 mA Vi = 3.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 4.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 4.5 V Io = 10 mA, Vi = 4.5 V -25 Typ. 2.5 Max. 2.525 2.55 18 Unit V V V mA mV mV mA mA A dB dB dB V 3 3 0.5 1.5 50 82 77 60 50 0.2 15 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE25C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 3.2 to 18 V, Io = 0.5 mA Vi = 3.5 V Io = 0.5 to 100 mA ON MODE Vi = 3.5 to 18 V Io = 0 mA Vi = 3.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 4.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 3.3 V o Io = 10 mA, Vi = 3.3 V -25 Typ. 2.5 Max. 2.55 2.6 18 Unit V V V mA mV mV mA mA A dB dB dB V 3 3 0.5 1.5 50 82 77 60 50 0.2 20 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 6/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE27AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 3.4 to 18 V, Io = 0.5 mA Vi = 3.7 V Io = 0.5 to 100 mA ON MODE Vi = 3.7 to 18 V Io = 0 mA Vi = 3.7 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 4.7 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 4.7 V Io = 10 mA, Vi = 4.7 V -25 Typ. 2.7 Max. 2.727 2.754 18 Unit V V V mA mV mV mA mA A dB dB dB V 3 3 0.5 1.5 50 82 77 60 50 0.2 15 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE27C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 3.4 to 18 V, Io = 0.5 mA Vi = 3.7 V Io = 0.5 to 100 mA ON MODE Vi = 3.7 to 18 V Io = 0 mA Vi = 3.7 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 4.7 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 4.7 V o Io = 10 mA, Vi = 4.7 V -25 Typ. 2.7 Max. 2.754 2.808 18 Unit V V V mA mV mV mA mA A dB dB dB V 3 3 0.5 1.5 50 82 77 60 50 0.2 20 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 7/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE30AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 3.7 to 18 V, Io = 0.5 mA Vi = 4 V Io = 0.5 to 100 mA ON MODE Vi = 4 to 18 V Io = 0 mA Vi = 4 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 5 V Io = 10 mA, Vi = 5 V -25 Typ. 3 Max. 3.030 3.060 18 Unit V V V mA mV mV mA mA A dB dB dB V 3 3 0.5 1.5 50 81 76 60 50 0.2 15 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE30C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 3.7 to 18 V, Io = 0.5 mA Vi = 4 V Io = 0.5 to 100 mA ON MODE Vi = 4 to 18 V Io = 0 mA Vi = 4 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 5 V o Io = 10 mA, Vi = 5 V -25 Typ. 3 Max. 3.060 3.120 18 Unit V V V mA mV mV mA mA A dB dB dB V 3 3 0.5 1.5 50 81 76 60 50 0.2 20 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 8/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE33AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 4 to 18 V, Io = 0.5 mA Vi = 4.3 V Io = 0.5 to 100 mA ON MODE Vi = 4.3 to 18 V Io = 0 mA Vi = 4.3 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 5.3 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o o Test Conditions Io = 10 mA, Vi = 5.3 V o Io = 10 mA, Vi = 5.3 V -25 Typ. 3.3 Max. 3.333 3.366 18 Unit V V V mA mV mV mA mA A dB dB dB V 3 3 0.5 1.5 50 80 75 60 50 0.2 15 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE33C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 4 to 18 V, Io = 0.5 mA Vi = 4.3 V Io = 0.5 to 100 mA ON MODE Vi = 4.3 to 18 V Io = 0 mA Vi = 4.3 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 5.3 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 5.3 V o Io = 10 mA, Vi = 5.3 V -25 Typ. 3.3 Max. 3.366 3.432 18 Unit V V V mA mV mV mA mA A dB dB dB V 3 3 0.5 1.5 50 80 75 60 50 0.2 20 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 9/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE35AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 4.2 to 18 V, Io = 0.5 mA Vi = 4.5 V Io = 0.5 to 100 mA ON MODE Vi = 4.5 to 18 V Io = 0 mA Vi = 4.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 5.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 5.5 V Io = 10 mA, Vi = 5.5 V -25 Typ. 3.5 Max. 3.535 3.57 18 Unit V V V mA mV mV mA mA A dB dB dB V 3 3 0.5 1.5 50 79 74 60 50 0.2 15 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE35C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 4.2 to 18 V, Io = 0.5 mA Vi = 4.5 V Io = 0.5 to 100 mA ON MODE Vi = 4.5 to 18 V Io = 0 mA Vi = 4.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 5.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 5.5 V o Io = 10 mA, Vi = 5.5 V -25 Typ. 3.5 Max. 3.57 3.64 18 Unit V V V mA mV mV mA mA A dB dB dB V 3 3 0.5 1.5 50 79 74 60 50 0.2 20 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 10/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE40AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 4.7 to 18 V, Io = 0.5 mA Vi = 5 V Io = 0.5 to 100 mA ON MODE Vi = 5 to 18 V Io = 0 mA Vi = 5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 6 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 6 V Io = 10 mA, Vi = 6 V -25 Typ. 4 Max. 4.04 4.08 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 78 73 60 50 0.2 20 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE40C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 4.7 to 18 V, Io = 0.5 mA Vi = 5 V Io = 0.5 to 100 mA ON MODE Vi = 5 to 18 V Io = 0 mA Vi = 5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 6 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 6 V o Io = 10 mA, Vi = 6 V -25 Typ. 4 Max. 4.08 4.16 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 78 73 60 50 0.2 30 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 11/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE45AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 5.2 to 18 V, Io = 0.5 mA Vi = 5.5 V Io = 0.5 to 100 mA ON MODE Vi = 5.5 to 18 V Io = 0 mA Vi = 5.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 6.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 6.5 V Io = 10 mA, Vi = 6.5 V -25 Typ. 4.5 Max. 4.545 4.59 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 77 72 60 50 0.2 20 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE45C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 5.2 to 18 V, Io = 0.5 mA Vi = 5.5 V Io = 0.5 to 100 mA ON MODE Vi = 5.5 to 18 V Io = 0 mA Vi = 5.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 6.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 6.5 V o Io = 10 mA, Vi = 6.5 V -25 Typ. 4.5 Max. 4.59 4.68 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 77 72 60 50 0.2 30 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 12/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE47AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 5.4 to 18 V, Io = 0.5 mA Vi = 5.7 V Io = 0.5 to 100 mA ON MODE Vi = 5.7 to 18 V Io = 0 mA Vi = 5.7 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 6.7 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 6.7 V Io = 10 mA, Vi = 6.7 V -25 Typ. 4.7 Max. 4.747 4.794 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 77 72 60 50 0.2 20 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE47C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 5.4 to 18 V, Io = 0.5 mA Vi = 5.7 V Io = 0.5 to 100 mA ON MODE Vi = 5.7 to 18 V Io = 0 mA Vi = 5.7 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 6.7 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 6.7 V o Io = 10 mA, Vi = 6.7 V -25 Typ. 4.7 Max. 4.794 4.888 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 77 72 60 50 0.2 30 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 13/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE50AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 5.7 to 18 V, Io = 0.5 mA Vi = 6 V Io = 0.5 to 100 mA ON MODE Vi = 6 to 18 V Io = 0 mA Vi = 6 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 7 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 7 V Io = 10 mA, Vi = 7 V -25 Typ. 5 Max. 4.05 5.1 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 76 71 60 50 0.2 20 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE50C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 5.7 to 18 V, Io = 0.5 mA Vi = 6 V Io = 0.5 to 100 mA ON MODE Vi = 6 to 18 V Io = 0 mA Vi = 6 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 7 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 7 V o Io = 10 mA, Vi = 7 V -25 Typ. 5 Max. 5.1 5.2 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 76 71 60 50 0.2 30 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 14/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE52AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 5.9 to 18 V, Io = 0.5 mA Vi = 6.2 V Io = 0.5 to 100 mA ON MODE Vi = 6.2 to 18 V Io = 0 mA Vi = 6.2 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 7.2 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 7.2 V Io = 10 mA, Vi = 7.2 V -25 Typ. 5.2 Max. 5.252 5.304 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 76 71 60 50 0.2 20 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE52C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 5.9 to 18 V, Io = 0.5 mA Vi = 6.2 V Io = 0.5 to 100 mA ON MODE Vi = 6.2 to 18 V Io = 0 mA Vi = 6.2 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 7.2 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 7.2 V o Io = 10 mA, Vi = 7.2 V -25 Typ. 5.2 Max. 5.304 5.408 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 76 71 60 50 0.2 30 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 15/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE55AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 6.2 to 18 V, Io = 0.5 mA Vi = 6.5 V Io = 0.5 to 100 mA ON MODE Vi = 6.2 to 18 V Io = 0 mA Vi = 6.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 7.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 7.5 V Io = 10 mA, Vi = 7.5 V -25 Typ. 5.5 Max. 5.55 5.61 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 76 71 60 50 0.2 20 15 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE55C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 6.2 to 18 V, Io = 0.5 mA Vi = 6.5 V Io = 0.5 to 100 mA ON MODE Vi = 6.5 to 18 V Io = 0 mA Vi = 6.5 to 18 V Io = 100 mA OFF MODE Vi = 6 V SVR Supply Voltage Rejection Io = 5 mA Vi = 7.5 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 7.5 V o Io = 10 mA, Vi = 7.5 V -25 Typ. 5.5 Max. 5.61 5.72 18 Unit V V V mA mV mV mA mA A dB dB dB V 4 3 0.5 1.5 50 76 71 60 50 0.2 30 25 1 3 100 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 6 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 16/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE60AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 6.7 to 18 V, Io = 0.5 mA Vi = 7 V Io = 0.5 to 100 mA ON MODE Vi = 7 to 18 V Io = 0 mA Vi = 7 to 18 V Io = 100 mA OFF MODE Vi = 9 V SVR Supply Voltage Rejection Io = 5 mA Vi = 8 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o o Test Conditions Io = 10 mA, Vi = 8 V Io = 10 mA, Vi = 8 V -25 Typ. 6 Max. 6.06 6.12 18 Unit V V V mA mV mV mA mA A dB dB dB V 5 3 0.7 1.7 70 75 69 57 50 0.2 25 15 1.6 3.6 140 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 9 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE60C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 6.7 to 18 V, Io = 0.5 mA Vi = 7 V Io = 0.5 to 100 mA ON MODE Vi = 7 to 18 V Io = 0 mA Vi = 7 to 18 V Io = 100 mA OFF MODE Vi = 9 V SVR Supply Voltage Rejection Io = 5 mA Vi = 8 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 oC o o Test Conditions Io = 10 mA, Vi = 8 V o Io = 10 mA, Vi = 8 V -25 Typ. 6 Max. 6.12 6.24 18 Unit V V V mA mV mV mA mA A dB dB dB V 5 3 0.7 1.7 70 75 69 57 50 0.2 35 25 1.6 3.6 140 eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 9 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 17/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE80AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 8.7 to 18 V, Io = 0.5 mA Vi = 9 V ON MODE Vi = 9 to 18 V Vi = 9 to 18 V Io = 0.5 to 100 mA Io = 0 mA Io = 100 mA Test Conditions Io = 10 mA, Vi = 10 V Io = 10 mA, Vi = 10 V -25 Min. 7.92 7.84 Typ. 8 Max. 8.08 8.16 18 25 15 1.6 3.6 140 Unit V V V mA mV mV mA mA A dB dB dB V OFF MODE Vi = 9 V SVR Supply Voltage Rejection Io = 5 mA Vi = 10 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.2 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 9 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE80C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 9 to 18 V, Vi = 9 V ON MODE Vi = 9 to 18 V Vi = 9 to 18 V Io = 0.5 mA Io = 0.5 to 100 mA Io = 0 mA Io = 100 mA Test Conditions Io = 10 mA, Vi = 10 V o Io = 10 mA, Vi = 10 V -25 Min. 7.84 7.68 Typ. 8 Max. 8.16 8.32 18 35 25 1.6 3.6 140 Unit V V V mA mV mV mA mA A dB dB dB V OFF MODE Vi = 9 V SVR Supply Voltage Rejection Io = 5 mA Vi = 10 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 9 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 18/25 LE00AB/C ELECTRICAL CHARACTERISTICS FOR LE120AB (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 12.7 to 18 V, Io = 0.5 mA Vi = 13 V ON MODE Vi = 13 to 18 V Vi = 13 to 18 V Io = 0.5 to 100 mA Io = 0 mA Io = 100 mA Test Conditions Io = 10 mA, Vi = 14 V Io = 10 mA, Vi = 14 V -25 Min. 11.88 11.76 Typ. 12 Max. 12.12 12.24 18 25 15 1.6 3.6 180 Unit V V V mA mV mV mA mA A dB dB dB V OFF MODE Vi = 13 V SVR Supply Voltage Rejection Io = 5 mA Vi = 14 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA -40 < Ta < 125 C o eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.2 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 oC -40 < Ta < 125 C Vi = 13 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 ELECTRICAL CHARACTERISTICS FOR LE120C (refer to the test circuits, Tj = 25 oC, Ci = 0.1 F, Co = 2.2 F unless otherwise specified) Symbol Vo Vi I out V o V o Id Parameter Output Voltage Operating Input Voltage Output Current Limit Line Regulation Load Regulation Quiescent Current Vi = 12.7 to 18 V, Io = 0.5 mA Vi = 13 V ON MODE Vi = 13 to 18 V Vi = 13 to 18 V Io = 0.5 to 100 mA Io = 0 mA Io = 100 mA Test Conditions Io = 10 mA, Vi = 14 V o Io = 10 mA, Vi = 14 V -25 Min. 11.76 11.52 Typ. 12 Max. 12.24 12.48 18 35 25 1.6 3.6 180 Unit V V V mA mV mV mA mA A dB dB dB V OFF MODE Vi = 13 V SVR Supply Voltage Rejection Io = 5 mA Vi = 14 V 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Io = 100 mA Io = 100 mA eN Vd V il V ih Ii CO Output Noise Voltage Dropout Voltage Control Input Logic Low Control Input Logic High Control Input Current Output Bypass Capacitance 0.4 0.5 0.8 V V V V A F -40 < Ta < 125 C -40 < Ta < 125 C Vi = 13 V, Vc = 6 V 2 ESR = 0.1 to 10 Io = 0 to 100 mA 2 10 10 19/25 LE00AB/C TYPICAL PERFORMANCE CHARACTERISTICS (unless otherwise specified T j=25oC) Dropout Voltage vs Output Current Dropout Voltage vs Temperature Supply Current vs Temperature Supply Current vs Input Voltage Short Circuit Current vs Dropout Voltage S.V.R. vs Frequency 20/25 LE00AB/C Logic Controlled Precision 3.3/5.0V Selectable Output Sequential Multi-Output Supply 21/25 LE00AB/C Multiple Supply With ON/OFF Toggle Switch Basic Inhibit Functions 22/25 LE00AB/C SO-8 MECHANICAL DATA DIM. MIN. A a1 a2 a3 b b1 C c1 D E e e3 F L M S 3.8 0.4 4.8 5.8 1.27 3.81 4.0 1.27 0.6 8 (max.) 0.14 0.015 5.0 6.2 0.65 0.35 0.19 0.25 0.1 mm TYP. MAX. 1.75 0.25 1.65 0.85 0.48 0.25 0.5 45 (typ.) 0.188 0.228 0.050 0.150 0.157 0.050 0.023 0.196 0.244 0.025 0.013 0.007 0.010 0.003 MIN. inch TYP. MAX. 0.068 0.009 0.064 0.033 0.018 0.010 0.019 0016023 23/25 LE00AB/C TO-92 MECHANICAL DATA mm DIM. MIN. TYP. MAX. MIN. inch TYP. MAX. A 4.58 5.33 0.180 0.210 B 4.45 5.2 0.175 0.204 C 3.2 4.2 0.126 0.165 D 12.7 0.500 E 1.27 0.050 F 0.4 0.51 0.016 0.020 G 0.35 0.14 24/25 LE00AB/C Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics (c) 1998 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. . 25/25 |
Price & Availability of LE120C
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |